Be careful removing the bike because the box has sharp staples holding it together. Some people recommend using pliers to remove the staples first, but I found it easier to just carefully pull the bike free; do which ever method works best for you. If your handlebars are tangled, proceed to rotate them around either clockwise or counter-clockwise to untangle them. Sadly I cannot give further instructions because it depends on how the handlebars tangle, but if you carefully look it over you should be able to follow the wires to straighten it all out. For those that are new to assembling mountain bikes you may find this article helpful. The instructions that comes with the Hyper Havoc FS Mountain Bike are very basic and show generalized pictures and instructions that sometimes aren’t very helpful.
The bike gears and peddles are slightly stiff, but I am sure it will loosen up with a bit of oiling and riding. I would recommend this bike if you are on a budget and need basic transportation for getting around because it does the job and serves its purpose. As far as cheap mountain bikes go, overall the Havoc Hyper FS mountain bike isn’t really all that bad. Use your 5mm hex key to adjust the screw at the top of the brake levers to rotate them around and set them in place. If your handlebars are on backwards this screw will be at the bottom of the brake lever. Make sure that they are comfortable and your wrists are not straining to use them.
The seat post simply slides in place, but first you should slide the light reflector on it and screw it in place. There should be a back quick release clamp that will hold the seat in place that attaches to the seat post, simply grab hold of the lever, clamp it down, and pull it tight to hold the bike seat in place. The basic rule of thumb is that the bike seat should be almost equal to the height of your waist, adjust the seat accordingly so that it is comfortable. Adjust the front brake pads by pulling the silver wire tight and holding it in place, then tighten the screw back up- You may need an extra pair of hands to do it correctly. You can tighten the tire’s nuts and the front brake’s cap by using an adjustable wrench. It loses three points for the small defects and bad customer service from the manufacturer and seller.
Carefully unscrew the cap slightly so that the brakes will loosen up, this will allow you to easily slide the tire on. There is a plastic safety stand at the bottom of the front tire fork that you will need to first remove from the bike, grab it and pull it down to remove it. The 20IN Hyper Ultra 40 E-Bike offers great value for its price with a range of features and specs. Its durable aluminum frame and replaceable battery ensure longevity and convenience. With a powerful 250W hub-integrated motor, this e-bike is a reliable and affordable option for those looking to embrace micromobility.
It is an aluminum frame and the tag that was attached to the bike says that it can hold about 275 lbs or so. I was a bit surprised by this because the manufacturer should have sent us the part since the bike was just ordered brand new and we had the order number and receipt. For a product that would have cost the company a minimum of $10 to ship out, I did find it a bit frustrating that their customer service was so poor and we ended up having to pay for the replacement ourselves. The next problem is that the hyper mountain bike bike seat is hard and uncomfortable, if you only ride short distances it isn’t a problem, but if you do between 2 through 5 miles you will start to feel it. The handlebars sometimes wobble and slide out-of-place, not at the base where it connects to the body, but literally at the center “T” joint at the top near where your hands are, it will slip out-of-place and slide around. I have tightened it a few times and it now finally stays in place, but it can be dangerous when it randomly slides over while riding.
This cutting-edge equipment provides a great way for riders to travel faster, farther, and more comfortably than ever before. There are two nuts on the front tire, one on the left side and one on the right. Proceed to slightly unscrew both nuts on the front tire so that you can slide it onto the front fork. Pull the brake pads out the way if you need to and slide the fork onto the tire. The Right pedal will be labeled with an “R” and the Left with an “L” sticker. If you’re running a script or application, please register or sign in with your developer credentials here.
For a product to be returned under our policy, that product must be in a resalable condition unless faulty or otherwise defective. It’s this policy that hyper bike provides you peace of mind while shopping at The Warehouse. Usually the order will be processed and ready for shipping within 1-2 business days.